Owon HDS1021M Uživatelský manuál Strana 43
- Strana / 64
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
OWON HDS1021M Handheld DSO & DMM 8-Advanced Function of Oscilloscope
8.2.2 Make Open and Close Settings on Channel
Press F2 Channel key first, then select OFF to make a Close setting on channel.
Press F2 Channel key first, then select ON to make an Open setting on channel.
8.2.3 Adjusting the Probe Scale
It is necessary to adjust the probe attenuation scale factor correspondingly in the channel operation
menu in order to comply with the probe attenuation scale. If it is a 10:1 probe, the scale of the
input channel of the oscilloscope should be selected as 10X to avoid any error occurring in the
displayed scale factor information and tested data.
Press F3 Probe to jump to the relative probe.
Table: Probe attenuation factor and the corresponding menu setting
Probe attenuation factor Corresponding Menu Setting
1:1 1X
10:1 10X
100:1 100X
1000:1 1000X
8.2.4 Setting of Inverted Waveform
Inverted waveform: The displayed signal reverses 180 degrees relatively to the ground potential.
Press F4 Inverted to start Invert; again press F4 Inverted to close Invert.
8.3 Setting the Trigger System
The Trigger defines the time when the acquisition of data and display of waveform start. If it is set
correctly, the trigger can turn an unstable display into a significant waveform.
When starting the acquisition of data, the oscilloscope collects sufficient data to draw the
waveform at the left side of the triggering point. With waiting for the triggering condition, the
oscilloscope is gathering data continuously. After a trigger is detected, the oscilloscope gathers
enough data continuously to draw the waveform at the right side of the triggering point.
To make a trigger mode setting, do the following:
1. Press the MENU key and the function menu appears at the right of the screen.
2. Press the MENU ▲ or MENU ▼ key to select TRIG MODE and five items selectable are
displayed at the bottom of the screen.
3. Select and press one from F1 through F5 key to make a different setting.
３６
- User Manual 1
- Mar. 2012 edition Ver1.1 2
- General Warranty 3
- Table of Contents 4
- 1.Declaration of Conformity 8
- 1.2 Package Contents 9
- 2.Safety Information 10
- 3. General Characteristics 13
- 5. Input Connections 15
- 6. Using the Scope 18
- 6.4 Navigating a Menu 20
- 6.7 Input Connections 23
- Position 24
- 6.11 Freezing the Screen 25
- 6.15 Selecting AC-coupling 28
- 7. Using the Multimeter 30
- 7.4.3 On-off Test 33
- 7.5 Freezing the Readings 38
- 8.1 About this Chapter 41
- 8.2 Setting the Channel 41
- 8.4 Triggering Control 44
- 8.4.2 Video Triggering 45
- 8.5 Acquiring Mode Setting 47
- 8.6 Display Setting 47
- 8.6.1 Display Style 48
- 8.6.2 Persistence 48
- 8.6.3 Cymometer 48
- 8.7 Waveform Saving Setups 49
- 8.8 Function Setting Menu 50
- 8.11 Autoscale 54
- 8.12 System State Menu 55
- System State 56
- 8.14 Data Transmission 57
- 9.Trouble Shooting 58
- 10.Appendix 59
- 2Hz to full bandwidth 60
- 10.1.2 Meter 61
- 20A ±3%±3 digits 10mA 61
- 100-240 V AC 50/60Hz 63
- Power output 8.5 VDC 63
- Current output 1500 mA 63
- 10.2.1 Common Maintenance 63
Související produkty a manuály pro Měřící nástroje Owon HDS1021M
Měřící nástroje Owon HDS Series Uživatelský manuál
(72 stránky)
(72 stránky)
Měřící nástroje Owon VDS Series Uživatelský manuál
(40 stránky)
(40 stránky)
Abus FU9050 Privest Wireless Vibration Detector manuály
Uživatelské manuály a uživatelské příručky pro Pro domov Abus FU9050 Privest Wireless Vibration Detector.
Poskytujeme 1 manuály pdf Abus FU9050 Privest Wireless Vibration Detector ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentáře k této Příručce